Fabriqué en Grande-Bretagne

Directement de notre usine

Livraison gratuite le lendemain

Pour toute commande supérieure à 750 £

Résultats du test produit

Tous les résultats des tests publiés

Conseils techniques d'experts

Appelez ou discutez avec notre équipe

A 5L white plastic container of Everflor Universal Dustproofer concrete floor sealer with a black cap and a black label featuring white and blue text.
EverFlor - UniSeal - Concrete Sealer - Wetlook - Everest Paints

Principales caractéristiques du produit

Dust Proofer

Seals Concrete Dust

Deep Penetrating

Binds Weak Concrete

Microporous

Allows Walls to Breathe

Water Based

Low Odour Formula

EverFlor - Durcisseur de surface universel

Dust ProofingDeep PenetratingBreathableWater Based

A clear acrylic dustproofer that hardens and seals weak, dusty concrete, screeds and masonry.

The resin soaks into the surface rather than sitting on top of it, binding loose material and cutting the dust that lifts off a worn floor underfoot and under wheels. The result is a firmer, less porous surface that stays colourless and still breathes. Use it on floors and walls, inside or outside, on concrete, screed, brick, blockwork, plaster and block paving.

En rupture de stock
869,00 kr
Configuration
Taille
Taille: 5 litres

Livraison et assistance technique

Expédition le jour même (pour toute commande passée avant 11h)

Achetez directement du fabricant

Nous livrons en Europe continentale

Support technique par des spécialistes en revêtement

Notre équipe technique peut vous aider pour la sélection des produits, la préparation des surfaces et les conseils d'application.

Contact Technical Support

Principales caractéristiques du produit

Dust Proofer

Seals Concrete Dust

Deep Penetrating

Binds Weak Concrete

Microporous

Allows Walls to Breathe

Water Based

Low Odour Formula

Stops the Dust. Hardens the Floor.

Weak screeds and poor quality concrete give up their surface a grain at a time. Foot traffic and wheels grind the top layer loose, and fine grey dust lifts off the floor as fast as it is swept away. A surface film only masks that; it sits on friable material and breaks up with it. This dustproofer is a colourless liquid resin that penetrates deep into the substrate and binds the loose layer from within, so the concrete itself is hardened and dustproofed. It is water based, virtually odourless and microporous, so the floor still breathes. One coat, straight from the container by brush, roller or spray, with no mixing and no thinning.
Cliquez sur une icône pour explorer les fonctionnalités Appuyez sur une icône pour explorer les fonctionnalités

Optimized Curing Profile

Engineered for efficient application cycles. The coating becomes touch-dry in just 2–4 hours (temperature dependent), preventing debris pickup and allowing for a reliable, streamlined application process on large surface areas.

Hydrophobic Vapor Valve

The advanced acrylic lattice acts as a "one-way valve." It blocks rain and surface oils from penetrating downwards but allows trapped ground moisture to escape as vapor—preventing the bubbling and blistering common with standard floor paints.

Deep Penetration Hardening

Weak screeds and poor quality concrete release dust because the surface fines are not bound together. The colourless dual acrylic resin soaks into the open pores and hardens within them, binding the loose material into the slab. The result is a dustproofed, strengthened surface with reduced porosity on concrete, brick, blockwork and plaster.

Single Pack Application

Nothing is mixed, thinned or primed. Apply one coat by brush, roller or spray straight from the container at 6m² per litre, working between 5°C and 30°C, indoors or out. Clean tools in warm soapy water.

Profil de performance

Single-Pack Water Based Acrylic Dustproofer. A colourless penetrating resin that hardens and dustproofs porous concrete, screed and masonry. One coat is normally sufficient. Touch dry in two hours at 20°C, fully cured in twelve. Applied by brush, roller or spray with no mixing and no thinning.

Télécharger la fiche technique
Coverage 6m²per litre, per coat
Coats 1Recommended
Touch Dry 2 hrsat 20°C
Finish ClearColourless

Informations essentielles

Détails du produit

Description

EverFlor Universal Dustproofer is a colourless liquid resin for porous concrete and similar absorbent materials. It penetrates deep into the substrate and binds the weak surface layer, so a floor that once released fine grey dust is left hardened and dustproofed. On brick, blockwork and plaster walls it reduces both porosity and dusting.

The product is a single pack, water based dual acrylic system. There is no solvent to flash off and it is virtually odourless, which makes it workable in occupied buildings. It is microporous, so the substrate can continue to breathe after treatment. It dries clear and leaves no colour change of its own.

No primer is required and no thinning is needed. Apply it as supplied by brush, roller or spray. One coat is normally enough. Because it reduces surface porosity, it is also useful as preparation on weak or dusty screeds before a floor coating is applied.

Recommended areas of use

  • Previously untreated concrete floors and screeds
  • Porous, bare concrete and sand and cement screeds
  • Brick and blockwork walls
  • Plastered walls that chalk or dust
  • Block paving
  • Interior and exterior surfaces

Features

  • Penetrates the surface to harden weak, dusty concrete rather than forming a film on top
  • Reduces porosity and dusting on brick, blockwork and plaster
  • Microporous, so the substrate continues to breathe
  • Water based and solvent-free, with a VOC content below 30 g/l
  • Virtually odourless, suitable for work in occupied areas
  • Colourless, so the appearance of the substrate is retained
  • Single pack with no mixing and no thinning; brush, roller or spray
  • Tools wash out in warm soapy water

Good to know

The substrate must be dry and absorbent for the resin to penetrate. If water poured on the surface is not taken in, the surface is too closed for treatment. Sweep off loose dust and dirt first, and remove oil and grease, then rinse and allow to dry. New concrete needs time to dry enough to absorb the liquid before treatment. Apply and store between 5°C and 30°C. Shelf life is 24 months.

Application

SURFACE PREPARATION

Little preparation is needed, but the surface must be dry and porous. Sweep the area to remove surface dust and dirt. Remove oil and grease with a suitable degreaser, rinse with water and allow the surface to dry.

Test absorbency if you are unsure. Pour some water onto the substrate: if it is absorbed easily, the surface is suitable. New concrete must first be dry enough to take up the liquid. No primer is required.

APPLICATION

Apply between 5°C and 30°C. Use as supplied — do not thin. Apply by brush, roller or spray, working the liquid well into the surface so the substrate absorbs as much as it can hold.

Avoid ponding. Do not let surplus unabsorbed liquid stand and dry on the surface; spread it out onto adjacent areas instead. One coat is normally sufficient. A second coat may be worthwhile on exceptionally porous substrates.

DRYING AND CURING

At 20°C the surface is touch dry in 2 hours and can be recoated after 4 hours. Allow 12 hours at 20°C for the cure to complete. Lower temperatures and poor drying conditions will extend all of these times.

CLEANING AND STORAGE

Clean brushes, rollers and spray equipment with warm soapy water immediately after use. Store unopened containers between 5°C and 30°C. Shelf life is 24 months.

Fichiers et fiches techniques

Le Centre de Connaissances

Tout ce que vous devez savoir

Parcourez notre collection d'articles détaillés et de guides pratiques conçus pour vous aider à tirer le meilleur parti de ce produit. Que vous ayez besoin d'aide pour la préparation des surfaces ou de conseils d'application, nous avons ce qu'il vous faut.

Afficher le Centre technique

A visual comparison of a mossy, weed-infested block paving driveway next to a freshly cleaned section in the UK.
  • par Sam Marriott

Restauration de pavés autobloquants : Élimination de la mousse, des mauvaises herbes et du lichen

Le pavage est le choix le plus populaire pour les allées au Royaume-Uni, mais il présente un défaut de conception majeur : Les joints. Ces milliers d'espaces entre les briques sont le terreau idéal pour les mauvaises herbes, la mousse...

Plus

An unbranded industrial floor scrubber being used to maintain the high-gloss shine on a polished concrete warehouse floor.
  • par Sam Marriott

Nettoyer en profondeur le béton poli sans ternir sa brillance

Le béton poli est souvent vendu comme l'option de revêtement de sol "sans entretien". C'est un mensonge. Oui, il est incroyablement durable. Il ne s'écaillera pas comme de la peinture. Mais si vous l'ignorez, ou pire – si vous le...

Plus

Two unbranded silver tins labeled Acid and Alkaline on an industrial concrete warehouse floor.
  • par Sam Marriott

Nettoyants pour béton acides ou alcalins : Lequel est le meilleur pour votre sol ?

Si vous entrez dans une quincaillerie et demandez un "nettoyant à béton", vous vous retrouverez probablement avec plusieurs options devant vous. La plupart des gens choisissent la bouteille avec l'étiquette d'avertissement la plus agressive, pensant que "plus c'est fort, mieux...

Plus

How to Sand a Painted Concrete Floor for Recoating
  • par Sam Marriott

Comment poncer un sol en béton peint avant de le repeindre

Dans notre guide Ponçage vs. Meulage : Préparation du béton précédemment peint, nous avons établi que si votre sol réussit le test d'adhérence par quadrillage, l'étape suivante pour un nouveau revêtement sera le ponçage. Choisir de poncer plutôt que de meuler vous fait économiser des centaines de livres...

Plus

FAQ

Veuillez consulter notre page FAQ pour en savoir plus.

How do I know whether my floor is porous enough to treat?
Pour a little water onto the surface. If it soaks in readily, the substrate is absorbent and the resin will penetrate. If the water sits on top, the surface is already sealed or too closed, and the product cannot do its job.
Do I need a primer first?
No. No primer is required and no thinning is needed. Sweep the surface clean, remove any oil or grease, let it dry, then apply the product as supplied.
How many coats should I apply?
One coat is the recommendation and is normally sufficient. A second coat may be worthwhile on exceptionally porous substrates. If you do apply a second coat, wait at least 4 hours at 20°C. Coverage is 6m² per litre per coat, so allow for the extra material.
Will it change the colour or look of the concrete?
No. The finish is clear and the resin itself is colourless, so the substrate keeps its own appearance. It is also microporous, which means the substrate can continue to breathe after treatment.
Can I use it outside, and how soon can the area be used?
Yes — it is suitable for interior and exterior use, including block paving, and can be applied to walls as well as floors. Apply between 5°C and 30°C. At 20°C the surface is touch dry in 2 hours and the cure is complete after 12 hours. Cooler or damper conditions extend both.

Vous n'avez pas trouvé votre réponse ?

N'hésitez pas à nous contacter